Type: Amateur HF transceiver
Frequency range:
10-80 m + WARC
3.5-4.0 MHz
7.0-7.3 MHz
10.0-10.5 MHz (RX only)
14.0-14.35 MHz
18.0-18.5 MHz (RX only)
21.0-21.45 MHz
24.5-25.0 MHz (RX only)
28.0-29.7 MHz
Tuning steps: 10 / 100 Hz, 1 KHz
Frequency stability:
Less than 100 Hz after 1 hour warmup @ room temperature
Less than 1 KHz @ -10 to +60°C (14 to 140°F)
Mode: AM / SSB / CW
Channels / memory management:
1 regular per band segment
RAM storage, relies on external power
Repeater shift / offset: No
Power supply: 13.8 VDC ±15%
Current drain / power consumption:
RX: ? mA
TX: Max 20 A
Antenna impedance / connector: 50 ohm / SO-239
Dimensions (W*H*D): 241*94*275 mm (9.49*3.7*10.83")
Weight: 6.4 Kg (14.11 lb)
Other features:PBT. VOX. NB. SWR-meter.
Receiver system: Quadruple conversion superheterodyne
1st IF: 39.7315 MHz
2nd IF: 9.0115 MHz
3rd IF: 455 KHz
4th IF: 9.0115 MHz
Sensitivity:
AM: 0.6 uV (10 dB S+N/N)
SSB/CW: 0.3 uV (10 dB S+N/N)
Selectivity:
AM 6 KHz (-6 dB), 18 KHz (-60 dB)
SSB/CW 2.4 KHz (-6 dB), 4.8 KHz (-60 dB)
CW-N (Optional) 600 Hz (-6 dB), 1.5 KHz (-60 dB)
Image rejection:
AF output power / speaker:2 W at ?% distortion / 8 ohm
External speaker connector:3.5 mm, 8 ohm
RF output power:
AM: 5-25 W
SSB (PEP): 5-100 W
CW: 5-100 W
Modulation system:
Max FM deviation (Factory set): No FM
Spurious emissions: Better than -50 dB
Microphone impedance / connector: 1.3 kohm / 8-pin (Metal screw ring connector)
Microphone input level: 120 mV (Typical)
AH-1 3.5-28 MHz mobile antenna
BC-10A Memory backup AC power supply
EX-195 Marker unit
EX-202 LDA unit for automatic band switching
EX-203 CW audio filter, 150 Hz (-6 dB)
EX-205 TRV unit for transverter switching
FL-30 2.3 KHz SSB narrow filter. IF: 9 MHz
FL-44 2.4 KHz SSB filter. IF: 455 KHz
FL-45 500 Hz CW narrow filter. IF: 9 MHz
HM-10 Scanning microphone
HP-1 Headphones
IC-2KL 500 W solid state linear amplifier
MB-5 Mobile mounting bracket
PS-15 AC power supply
SM-5 Electret condenser type desk microphone
SP-3 External speaker
All reproductions on this site are free to use for non-commercial purposes unless you are the original copyright holder. I do not claim ownership of any reproduced content. I have tried to the best of my abilities to accurately reproduce the information, but some pages were hard to read, including photos or schematics. Many of these were scans or photocopies of varying quality and resolution.